atair8
07/07/2011, 07:55 PM
بسم الله الرحمن الرحيم
السلام عليكم ورحمة الله وبركاته
يا شباب الي يعرف يترجم النص هذا بطريقة واضحة
سويت ترجمة في قوقل وما فهمت النص كامل
الله يوفقكم جميع . بانتظاركم
1. Start with key out of ignition, drivers door is open all others closed and×
××××drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
××× A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
××××××× starting with lock. Use an even pace and try to go about one cycle per second.
××××××× (1Cycle× = 1 lock and 1 unlock).
××× B. Close, then open drivers door.
4.×Perform these steps within 40 seconds.
××××A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
××××××× starting with lock. Use an even pace and try to go about one cycle per second.
×××××××× (1Cycle× = 1 lock and 1 unlock).
××× B. Insert the key in the ignition cylinder.
××× C. Turn the ignition to ON (Do NOT Start) then back to OFF.
××× D. Remove the key from the ignition.
5. Within 3 seconds the power door locks should cycle automatically indicating successful
××× entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
××× A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
××× B. Immediately after letting go of the lock and unlock buttons, press the lock button by
××××××× itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
××××××× indicating successful programming. If the door locks do not cycle, or cycle twice.
××××××× repeat steps A and B in step 6 as your remote has not been accepted.
××× C. Repeat steps A and B in step 6 for each new remote.
7. Close drivers door.
××× Disclaimer
السلام عليكم ورحمة الله وبركاته
يا شباب الي يعرف يترجم النص هذا بطريقة واضحة
سويت ترجمة في قوقل وما فهمت النص كامل
الله يوفقكم جميع . بانتظاركم
1. Start with key out of ignition, drivers door is open all others closed and×
××××drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
××× A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
××××××× starting with lock. Use an even pace and try to go about one cycle per second.
××××××× (1Cycle× = 1 lock and 1 unlock).
××× B. Close, then open drivers door.
4.×Perform these steps within 40 seconds.
××××A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
××××××× starting with lock. Use an even pace and try to go about one cycle per second.
×××××××× (1Cycle× = 1 lock and 1 unlock).
××× B. Insert the key in the ignition cylinder.
××× C. Turn the ignition to ON (Do NOT Start) then back to OFF.
××× D. Remove the key from the ignition.
5. Within 3 seconds the power door locks should cycle automatically indicating successful
××× entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
××× A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
××× B. Immediately after letting go of the lock and unlock buttons, press the lock button by
××××××× itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
××××××× indicating successful programming. If the door locks do not cycle, or cycle twice.
××××××× repeat steps A and B in step 6 as your remote has not been accepted.
××× C. Repeat steps A and B in step 6 for each new remote.
7. Close drivers door.
××× Disclaimer